Tagformance Pro UHF 14.0

Tagformance-UHF_Software_Package_14.0.5

Date published: November 26, 2024
Note: The original 14.0.0 was released on July 9, 2024.

Version 14.0.5 is a patch version, replaces 14.0.4, and is the only downloadable version.

Issues fixed by patch versions since version 14.0 initial release:

  • fix the issue of the scripter no longer executing rows of a script where the frequency and power setting were done in a way that the UI validation would not have accepted it, e.g., the start frequency being 900 MHz when the script is run and script doing stopf=880, startf=860
  • add read data interpretation also to miller4 320k so that the responses from the tag are decoded and the data can be plotted
  • Threshold: fix incorrect Power On Tag Forward values on the secondary graph during measurement; caused by m/ft conversion and only incorrect during the measurement and in the secondary graph
  • Resolved an issue where selecting a measurement on the measurement list would cause the incorrect measurement to be highlighted on the secondary graph
  • Improved legend consistency in Link Budget Tab: corrected a problem where the measurement legend was overriding the link budget tab legend
  • SW-API in UHF mode now returns all read data as per the provided parameters

Please extract the .zip and run setup.exe to install the software.

Contents of the package

  • Tagformance UHF Installer
    • Tagformance 14.0 (v14 license required)
    • Update Tool 1.1.0 (for Tagformance Pro)
    • Tagformance Pro Firmware 6.0.0
  • Tagformance Pro Manual
  • Tagformance Pro Quick Start Guide
  • Tagformance Pro SW-API manual

What’s New

Note: this release is license controlled and a version 14 license is needed. If you are enrolled in the Tagformance Maintenance Program you have received the license file by email. In case you have not received the license, please request from support@voyantic.com stating your Tagformance Pro device serial number.

If you are not yet enrolled in the Maintenance Program sales@voyantic.com is happy to give a quotation for the Maintenance Program or Software Update.

  • Improvements
    • ARC pre-test feature: all specifications match the ARC released (https://rfid.auburn.edu/documents/) specification status at the time of release
    • Details
      • Y updated to version 2
      • Y2 added
      • C2 added
      • H updated to version 1.1
        • no changes to measurement though (highlight pen removed from document)
      • F updated to version 1.1
        • remove 2, 10 Denim
        • add Plastic3
      • I updated to version 2.1
        • remove 1, 2 polybag
        • remove 2, 10, multi Denim
        • add MIP 1.27cm
        • add plastic3
      • L updated to version 1.1
        • MIP 2.54 to 1.27
        • remove 2,10 Denim
        • add Plastic3
      • Q (was unversioned) updated to version 2
        • change Plastic to Plastic3
        • remove 2 Denim
      • R updated to version 3.1
        • MIP 2.54 to 1.27
      • Y2 updated to version 1.1
        • MIP 2.54 to 1.27
      • Removed G, J, K, N, W1, W3, W4
        • these are still available, just removed from the default category selection which is user-editable
      • W2, W5, W6 updated to version 1.1
        • remove 10 denim
        • MIP 2.54 to 1.27 (edited) 
  • Bugs fixed
    • Read Range measurement “theoretical read range reverse” y-axis does not update on unit selection
    • memory management: if custom read fails, the UI will unselect user’s selection
    • opt-in to analytics setting is reset in update (user is asked after every software update)
    • “adverse network conditions indicator” is removed – it was not relevant and it was non-standard UI component
    • Some measurement settings are not remembered even though “remember sweep settings” is enabled in “options”; also the “threshold sweep” range is not remembered but taken from license
    • “about” dialogue:
      • show ID does not toggle ID
      • expiry dates are hidden
    • Select command cannot be used in Protocol Testing Suite